Altronix AL1024ULXB2 Installation Instructions User Manual download pdf

Agency Listings:

• ULRecognizedcomponentforAccessControl

 SystemUnits(UL294),PowerSuppliesfor

 FireProtectiveSignalingSystems(UL1481).

Input:

• Input115VAC/60Hz,4.2amp.

Output:

• 24VDCoutput(UL1481).

• 8ampcontinuoussupplycurrentwith10amp

 supplycurrentduringalarm.

• 24VDC@10amp.(UL294).

• Filteredandelectronicallyregulatedoutput.

• MaximumRipple:250mVP/P

Battery Backup:

• Built-inchargerforsealedleadacidorgeltypebatteries.

Battery Backup (cont’d):

• Maximumchargecurrent3.6amp.

• Automaticswitchovertostand-bybattery

 whenACfails.

• Zerovoltagedropwhenswitchedovertobatterybackup.

Visual Indicators:

• ACinputandDCoutputLEDindicators.

Supervision:

• ACfailsupervision(form“C”contacts).

• Lowbatteryandbatterypresencesupervision

 (form“C”contacts).

Additional Features:

• Shortcircuitandthermaloverloadprotection.

Board Dimensions (W x L x H approximate):

4.5”x8.4”x1.9”(114.427mmx213.36mmx49.657mm)

Stand-by Specifications:

Output

15 min. of Stand-by &

5 min. of Alarm

4 hr. of Stand-by &

5 min. of Alarm

24 hr. of Stand-by &

5 min. of Alarm

60 hr. of Stand-by &

5 min. of Alarm

24VDC/12AH

Battery

Stand-By=8amp

Alarm=10amp

Stand-By=1.5amp

Alarm=10amp

Stand-By=200mA

Alarm=10amp

Stand-By=100mA

Alarm=10amp

Output

15 min. of Stand-by &

5 min. of Alarm

4 hr. of Stand-by &

5 min. of Alarm

24 hr. of Stand-by &

15 min. of Alarm

60 hr. of Stand-by &

15 min. of Alarm

24VDC/65AH

Battery

-----------------------------------------------

Stand-By=8.0amp

Alarm=10amp

Stand-By=1.5amp

Alarm=10amp

Stand-By=500mA

Alarm=10amp

Installation Instructions:

TheAL1024ULXB2shouldbeinstalledinaccordancewitharticle760ofTheNationalElectricalCodeaswellas

NFPA72andallapplicableLocalCodes.

1. MounttheAL1024ULXB2inthedesiredlocation/enclosure.

2. ConnectunswitchedACpower(115VAC60Hz)totheterminalsmarked[L,N](Fig. 1, pg. 2).Use14AWGorlarger

 forallpowerconnections(Battery,ACinput,DCoutput).Use22AWGto18AWGforpower-limitedcircuits

 (ACFail/LowBatteryreporting).

 Keep power-limited wiring separate from non power-limited wiring

(115VAC / 60Hz Input, Battery Wires). DC output Minimum 0.25” spacing must be provided.

3. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.

4. Connectdevicestobepoweredtotheterminalsmarked[+DC--](Fig. 1, pg. 2).

5. ForAccessControlapplicationsbatteriesareoptional.Whenbatteriesarenotused,alossofACwillresultinthe

 lossofoutputvoltage.Whentheuseofstand-bybatteriesisdesired,theymustbeleadacidorgeltype.Connect

 batterytoterminalsmarked[--BAT+](Fig. 1, pg. 2).

6. ItisrequiredtoconnectappropriatesignalingnotificationdevicestoACFAIL&BATFAIL(Fig. 1, pg. 2)

 supervisoryrelayoutputs.Use22AWGto18AWGwires.ACFAILwillreportin5minutes.

 Todelayreport6hourscut“ACDelay”jumper(Fig. 1a, pg. 2).

Maintenance:

Unitshouldbetestedatleastonceayearfortheproperoperationasfollows:

Output Voltage Test:Undernormalloadconditions,theDCoutputvoltageshouldbecheckedforpropervoltagelevel.

Battery Test:Undernormalloadconditionscheckthatthebatteryisfullycharged,checkspecifiedvoltagebothat

batteryterminalandattheboardterminalsmarked[--BAT+]toensurethereisnobreakinthebatteryconnectionwires.

Note:Maximumchargingcurrentunderdischargeis3.6amp.

Note:Expectedbatterylifeis5years;however,itisrecommendedchangingbatteriesin4yearsorlessifneeded.

AL1024ULXB2 - UL Recognized

Power Supply/Charger Rev.082312

Overview:

TheAL1024ULXB2isapowersupplythatconvertsa115VAC/60Hzinput,toa24VDCnonpower-limitedoutput

(seespecifications).

Specifications:

1 2

Summary of Contents

Page 1 - AL1024ULXB2 - UL Recognized

Agency Listings:• ULRecognizedcomponentforAccessControl SystemUnits(UL294),PowerSuppliesfor FireProtectiveSignalingSystems(UL1481)

Page 2 - Terminal Identification:

LED Diagnostics:Red (DC) Green (AC) Power Supply StatusON ON Normaloperatingcondition.ON OFF LossofAC,Stand-bybatterysupplyingpower.OFF ON No

Comments to this Manuals

No comments

Altronix AL1024ULXB2 Installation Instructions User Manual

Browse online or download User Manual for Accessories for electrical Altronix AL1024ULXB2 Installation Instructions. Altronix AL1024ULXB2 Installation Instructions User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for electrical Altronix AL1024ULXB2 Installation Instructions