Altronix SMP3PMP8CB Installation Instructions User Manual download pdf

SMP3CTXseries

Power Supply Voltage Output Specifications: *

Output VDC Switch Position Max. Load DC

12VDC

SW1 - Closed

ig. 1b, pg. 3)

2.5 amp

24VDC SW1 - Open

(Fig. 1b, pg. 3) 2.5 amp

*Specified at 25˚ C ambient.

Installation Instructions:

iring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local

codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the

enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s

upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the

enclosure. Drill the lo

er holes and install the three f

asteners. Place the enclosure’

s upper keyholes over the two

upper screws. Install the two lower screws and make sure to tighten all screws

(Enclosure Dimensions, pg. 4).

Secure enclosure to earth ground.

Set SW1 on the po

er suppl

y board to the desired DC output v

oltage

er Suppl

olta

ge Output Specification Chart)

SMP3CTX Series Power Supply Configuration Reference Chart:

Overview:

These units will con

vert a 115VAC or 230VAC, 50/60Hz input, into a regulated 12VDC or 24VDC output up 2.5 amp of

continuous load current (see specifications).

Specifications:

• Universal 115/230VAC input.

• Maximum charge current .5 amp.

• Filtered and electronically re

gulated outputs.

• Built-in charger for sealed lead acid or gel type batteries.

• Automatic switch over to stand-by battery when

AC fails (zero voltage drop).

• AC input and DC output LED indicators.

• Short circuit and thermal overload protection.

• Complete with power supply, power distribution module

hen applicable), enclosure, cam lock & battery leads.

• Power on-off switch.

Supervised models only:

• AC fail supervision (form "C" contacts).

• Low battery supervision (form "C" contacts).

SMP3CTX Series - Installation Guide

SMP3CTX - 1 - - - - .65 / .35 2.5

SMP3PMCTX - 1 - - - x .65 / .35 2.5

SMP3PMCTXX - 1 - - - x .65 / .35 2.5

SMP3PMP4 PD4 4 x - 3.5 x .65 / .35 2.5

SMP3PMP4CB PD4CB 4 - x 2.5 x .65 / .35 2.5

SMP3PMP8 PD8 8 x - 3.5 x .65 / .35 2.5

SMP3PMP8CB PD8CB 8 - x 2.5 x .65 / .35 2.5

SMP3PMP16 PD16W 16

x - 3.5 x .65 / .35 2.5

SMP3PMP16CB PD16WCB 16 - x 2.5 x .65 / .35 2.5

Altronix

Model Number

Accessory Power

Distribution

Module(s)

Number of Outputs

Fused Outputs

PTC Outputs

Individual Output

Rating (amp)

115VAC / 230VAC

Input Current (amp)

12/24VDC Total

Output Current (amp)

Supervised

1 2 3 4

Summary of Contents

Page 1 - *Specified at 25˚ C ambient

SMP3CTXseries-1-Power Supply Voltage Output Specifications: *Output VDC Switch Position Max. Load DC12VDCSW1 - Closed (Fig. 1b, pg. 3)2.5 amp24VDC SW1

Page 2 - Terminal Identification:

- 2- SMP3CTXseries3. Connect AC power to terminals marked [L & N], connect ground to terminal marked [G] (if used).Use 18 AWG or larger for all po

Page 3 - CLOSED - 12VDC

SMP3CTXseries-3-L G NOFF ONOPEN - 24VDCCLOSED - 12VDC5A 250VPowerDistributionModule(s)Power SupplyBoardCAUTION: De-energize unit prior to servicing.Gr

Page 4 - RightLeft

- 4- SMP3CTXseriesAltronix is not responsible for any typographical errors. Product specifications are subject to change without notice.Altronix Corp.

Comments to this Manuals

No comments

Altronix SMP3PMP8CB Installation Instructions User Manual

Browse online or download User Manual for Accessories for electrical Altronix SMP3PMP8CB Installation Instructions. Altronix SMP3PMP8CB Installation Instructions User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for electrical Altronix SMP3PMP8CB Installation Instructions