Altronix AL1002ULADA Installation Instructions User Manual download pdf (Page 3)

AL1002ULADA - 3 -

Power Supply Specifications:

AC Input:

120VAC60Hz,5amp.

Output:

Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.

One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised

totaloutputcurrentmustnotexceedcurrent10ampinAlarmCondition.

Battery:

Usetwo(2)12VDC/12AHortwo(2)12VDC/7AHbatteriesconnectedinseries.

Stand-by/Alarm Current

Consumption:

130mA/300mA

EOL Resistor

(end of line):

2.2K(2200ohm),AltronixModel#AL-EOL22(included).

Ground fault maximum

test impedance:

1000ohm.

Stand-by Specifications:

Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current Aux. Output

24VDC/7AH 24Hours 10amp/5minutes ---

24VDC/12AH

(usetwo(2)12VDCbatteriesinseries)

24Hours 10amp/5minutes 50mA

24VDC/36AH 24Hours 10amp/5minutes 1amp

Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power

outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for ratings. When

loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 10 amp total

alarm current (example: AUX = 1 amp, outputs up to 9 amp).

Installation Instructions:

WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA

72/ANSI,andwithalllocalcodesandauthoritieshavingjurisdiction.

Productisintendedforindooruseonly.

 Carefully review:

Application Guide for AL602ULADA, AL802ULADA, AL1002ULADA

Power Supply Specifications (pg. 3)

Stand-by Specifications (pg. 3)

Output Programming Selection Table (pg. 4)

Sync Mode Selection Table (pg. 4)

Terminal Identification Table (pgs. 5-6)

LED Status Indication Table (pg. 6)

1.Mountunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholes

 intheenclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placethe

 enclosure’supperkeyholesoverthetwoupperscrews,levelandsecure.Markthepositionofthelowertwoholes. 

 Removetheenclosure.Drillthelowerholesandinstallthetwofasteners.Placetheenclosure’supperkeyholesover 

 thetwoupperscrews.Installthetwolowerscrewsandmakesuretotightenallscrews

 (Enclosure Dimensions, pg. 12).

2. Connectgreenleadtoearthground (Fig 1).Connecttheline(L)andneutral(N)terminalstoaseparateunswitched

 ACcircuit(120VAC,60Hz)dedicatedtotheFireAlarmSystem.

3. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.

4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).

 Note:IfbatteriesbeingusedinyourinstallationdonotfitintotheAL1002ULADAunit,itisrequiredtoinstalla

 separateenclosure,ULListedforappropriateapplication.Separatebatteryenclosureisrequiredtohave50cubicinches

 ofadditionalopenspace.AllwiringmethodsshallbeinaccordancewiththeNationalElectricalCodeNFPA70/ 

 NFPA72/ANSIandwithalllocalcodesandauthoritieshavingjurisdiction.Batterycircuitsarenotpower-limited; 

 provide0.25”spacingfrompower-limitedcircuitsanduseseparateknockout.Ifadditionalbatteryenclosure

 isrequired,itmustbeULListedfortheapplicationandmountedwithin5’oftheAL1002ULADAenclosureinthe

 sameroom;minimum12AWGwireinappropriateconduitisrequiredforconnection.Whenusingconduit,make

 sureitisinstalledinamatterwhereitcannotturn.

5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]and

 desiredoutputsignaltype (Output Programming Selection Table, pg. 4).

L N

line

ground

neutral

Fig. 1

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

Altronix AL1002ULADA Installation Instructions User Manual Page 3

Comments to this Manuals

Related products and manuals for Accessories for electrical Altronix AL1002ULADA Installation Instructions