Altronix AL1002ULADA Installation Instructions User Manual download pdf (Page 8)

- 8 - AL1002ULADA

Optional hookups:

1- BatteryandACmonitoring:ACorBatteryFailconditionwillcausethecommontroubleinput[C“FAULT”NC]to

 reportbacktotheFACPviainput1andinput2.Thecommontroubleinputmayalsobeusedforotheroptional 

 supervisorymonitoring.

 ToreportACandBatteryTroubleconnectthebatteryandACFailrelayoutputshownin(Fig. 3a, Pg. 8)tothe

 commontroubleinput.

2- Drycontactinput(C“DRY1”NC)(C“DRY2”NC)canbeusedtoalarmoutputfroman

 addressablemodule(theseinputsareunidirectionandcannotreportbacktotriggermodule).

 Connection to triggering devices must be made within 20ft. of distance and using conduit for wiring.

3- Auxiliaryoutput(-AUX+)24VDCat1ampmax.

4- ACLocal[NC,NO,C]shouldconnecttothehostcontrolpanelforlocalannunciationof

 thetroublecondition.

Note: Ifcommontroubleinput,terminalsmarked[C“FAULT”NC]arenotused,theseterminalsmustbe

 shorted(connectjumper)toremaininactive.Foroptionalhookups(Fig. 3b, Pg. 8).

Optional Hookup Diagram:

Fig. 3

Maintenance:

Unitshouldbetestedatleastonceayearfortheproperoperationasfollows:

Output Voltage Test:Undernormalloadconditions,theDCoutputvoltageshouldbecheckedforpropervoltagelevel

(26.2-26.4VDC recommended range).

Battery Test:Undernormalloadconditionscheckthatthebatteryisfullycharged.Checkspecifiedvoltage

bothatbatteryterminalandattheboardterminalsmarked[+BAT--]toensurethatthereisnobreakinthebattery

connectionwires.

Fuses:Checkinputandoutputfusesonthepowersupplyboard,replaceifnecessary.Inputfuseratingis6.3amp@

250V,Outputfuseratingis15amp@32V.

Note:Maximumchargingcurrentis1.5amp.

Note:Expectedbatterylifeis5years;however,itisrecommendedchangingbatteriesin4yearsorlessifneeded.

These circuits are used to monitor AC and

Bat Fail and will cause a simultaneous trouble

condition to the FACP's IN1 and IN2 (Non-Supervised)

4-wire Smoke

Detector

4-wire Smoke

Detector

Fire Alarm

Control Panel

(FACP)

EOL Power

Supervision Relay

(Not Supplied)

EOL

Resistor

from FACP

SW1

-- DC +

SW2

+ OUT1 --

OUT1 OUT2 OUT3 OUT4

INP1 INP2

FAULT

NC C NO C "FAULT" NC

OUT1 OUT3

OUT2 OUT4

INPUT SELECT

TEMPORAL

STROBE SYNC

IN > OUT SYNC

IN1+

IN1--

IN2--

IN2+

C "DRY1" NC

RET1+

RET1--

RET2--

RET2+

C "DRY2" NC

+ OUT2 --

+ OUT3 --

+ OUT4 --

INPUT SELECT

TEMPORAL

STROBE SYNC

IN > OUT SYNC

-- AUX +

UPPER TERMINALS

LOWER TERMINALS

Addressable Control

Module Trigger Output

See Note 2

(Non-Supervised)

RESET

Supervised

Non-Supervised

Input from

Power Supply

BAT FAIL

AC FAIL

DC AC

AC DELAY

NC C NO NC C NO

AC LOCAL

NC C NO

6.3A 250V

Digital Communicator

or Local Annunciator

Dry output Contact

(Form "C" contacts)

Power-Limited Outputs

2.5 amp per output in alarm

Total = 10 amp

(Supervised)

AC FAIL

NC C NO

BAT FAIL

NC C NO

Fig. 3a

-- DC +

OUT1 OUT3

OUT2 OUT4

INPUT SELECT

TEMPORAL

STROBE SYNC

IN > OUT SYNC

INPUT SELECT

TEMPORAL

STROBE SYNC

IN > OUT SYNC

RESET

Fig. 3c

TroubleMemory

ResetButton

Fig. 3b

Common

trouble

Input/Output

NC CNOC "FAULT" NC

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Altronix AL1002ULADA Installation Instructions User Manual Page 8

Comments to this Manuals

Related products and manuals for Accessories for electrical Altronix AL1002ULADA Installation Instructions